Next, the sleeves are sewn päälisen pääliseen. Ie the setting of the side seam to cuff and sewn fro

Monthly model we chose Burda November 2012, on page number bedeck 100 girls pontson (model number 156). The compounds of formula smallest size of 122/128 and insisted on a slightly smaller pontson, one reduced the size of the pattern, that is, about the size of 110/116. In addition, the linings pontson and we put the buttons instead of a zipper in front. Pontso was gray polar fleece (fleece you can find here) and vuoritettiin red Tähtitrikoolla (JNY Red Star Jersey), chain 45cm chain ring (ring chains bedeck you can find more online store). Work start ... First we drew the front piece of the formula, as well as the size of the size 122/128 134/140 within each other as they are formula-sheet is. Formula paper we used a straight edge keskietukohdassa and because the front will be the zipper, then the formula is drawn keskietumerkistä run.
Then we started to reduce bedeck the formula. Draw the formula corners of the lines that pass through the formula of both the size of the angles bedeck through, look at the picture of the red lines. Along the measured difference in the sizes and patterns drawn on the inside of the corresponding measure from the marker. This is a very good help rectangular / triangular ruler, because it has those dimensions to zero on both sides just in time.
When the corners are drawn in the characters can be guides (the red lines in the figure) to draw the rest of the formula, in order to obtain sufficient alignment. Through these signs then drawn on the new formula on the inside of the above. Since we are using will kolmioviivotin, will be able to help in drawing alignment without guides easily. The compounds of formula kolmioviivottimen straight section will therefore be at an angle of 90 degrees to the passing line.
When all the components of the formula have been drawn and reduced, to check that the formula is reduced to the quite the same model as the original and cut patterns. Attached to the needle by the formulas and cut into pieces, as well päälikankaasta that the lining fabric.
Next, the sleeves are sewn päälisen pääliseen. Ie the setting of the side seam to cuff and sewn from this collar or collar down and just before the side seam / hiahnsuuta run "out", ie not sew it onto the mountains! bedeck
Now pontso then turned in the correct position, the second sleeve bedeck seam is therefore still open! Then, the second sleeve seam sewing closed. This item must remember to leave it to the back hole, big enough for one.
Next, sew darts hoods and hoods closed so that the Ovandel pääliseen and mountain mountains. If you want drawstring hood as we put, then make the hood before attaching the cord holes in the hood edge. Here we made a pretty ordinary buttonholes, and we supported that small pieces of fleece jersey, so that the machine is not would be grinding away to place a soft fleece läpeä when making.
Then sew helmasauman, after which we move the zipper sewing. Then the needle to the tire chain at that keskietukappaleiden between. Tip! Before bedeck ompleua bedeck you should check that the chain goes to the correct direction of pull there päälikankaan side.
Sewn chain and if tricot is now attempting to go the extra mile, then fed it gently with your fingernail (or a nail or the like with the device) fabric under the presser foot care. When the chain portion is sewn, the leading edges of the hoods can be sewn with overlock.
Now, translated from the back through the hole pontso the correct direction. Sewn onto the back aperture and topstitch them cuffs, hem and zipper bedeck edge. Nyörikuja sewn to the edge of the hood. Hoods can be sewn onto the collar processed areas in such a way that puts the needle collar and hood positions on the seams and sew a seam along the groove hoods to each other (this is not necessary). Stitching then steamed or ironed carefully. Pass the string to the edge of the hood. We did not separate from the cords with tassels.
If you do not happen to own the shop sold tupsuntekolaitteita and the method has been forgotten, so this refreshing memory a little help. Cut two circles of cardboard. Circle model, we took a tape roll inside the ring. Plotted as a circle, therefore, the amount of the finished tassel size. Ready tassel is about one centimeter to two smaller in diameter than it is now plotted as a circle.
Wind the thread until the middle part is almost full. Turn off the tupsulanka. At this point, we tightened those fish wires tightly in my hand. Now we need scissors, kapeateräiset and sharp is the best. Contact tassel tightly in your hand and your scissors bedeck blade gently between the pahviympyröiden. Cut the outer periphery of the cross wires. If you do not put the tension between the first thread, so please before cutting a piece of even produce tupsulankaa next and insert it between now pahviympyröiden while cutting (or cut all the wires cross the outer periphery).
Tie the fishing wire / tensioning wire tightly. We used the fish wire, as it will take to tighten, and certainly not at this stage, click into the cross-contaminate all the work. When the thread is tightened, remove the cardboard circles.
About me
Prym rengasnepparit can be attached to a pair of pliers or a hammer. Prym Vario nepparip